Stitched In Place.

Our stitched in place tool belts are designed from years of building and testing on the job site. The pursuit of the most efficient tool placement is driven by a high standard for efficiency and never wanting to waste a second while on the job. Choose a set up that best suits you or go with the B-Max, our flagship tool belt. Luke designed the B-Max as his personal set up and the pinnacle design for extreme efficiency as far as we’re concerned.

Details

Trimmer

$210.50$240.05

The Trimmer is a light and small front worn (tape at the front) all leather tool belt intended for finish carpentry. Designed for those carpenters that prioritize minimalism and convenience. Includes diagonal hammer sleeve, bit index, diagonal bar sleeve, optional suspender mounts and micro square slot, and much more. Read the “Details” section for a complete list of features.

Details

B-Mini

$317.60$376.69

Streamlined, efficient, and lightweight front worn tool belt. The B-Mini is ideal for those looking to minimize weight without losing effectiveness. Recommended for light framing, finishing, siding, renovations, project management, and general construction.

 

Note: 30 or smaller waist size will impact tape location making it slightly off centre, also the front tape clip will be removed.

Details

Framer F

$262.20$321.29

The Framer F is a front worn tool belt (tape measure in the front) with practical features for jobs ranging from concrete work to finish carpentry. Standard features include a stick nail sheath, hideaway hook, suspender mounts, rafter square slot, two diagonal bar sleeves, and more. Choose your preferred outer bags to complete your ideal front worn Framer. Read the “Details” section for a full list of features.

 

Note: The Framer F is 25″ long from the outside edge of left side bag to the outside edge of the right side bag. You can mark a rope or use a tape measure to wrap it around the front of your waist to see where the rear edges of the bags will end.

Details

Framer R

$262.20$321.29

The Framer R is a rear worn tool belt (tape measure at the back) with practical features for jobs ranging from concrete work to finish carpentry. Standard features include a stick nail sheath, hideaway hook, suspender mounts, rafter square slot, two diagonal bar sleeves, and more. Choose your preferred outer bags to complete your ideal rear worn Framer. Read the “Details” section for a full list of features.

 

Note: For those with a pant size 36 and larger, the bags on the Framer R sit further behind you than at your sides. The Framer R is 25″ long from the outside edge of left side bag to the outside edge of the right side bag. You can mark a rope or use a tape measure to wrap it around your back and see where the front edges of the bags will end.

Details

B-Max

$343.45$413.62

Designed as the ultimate front worn leather tool belt for carpenters. This feature rich setup includes a front quick release clip, suspender mounts, tool loops, drill clips, diagonal bar sleeves, hideaway hook, and so much more. Choose your left side outer bags to complete your ideal B-Max. For a complete list of features click on our “Details” section.

 

Note: 30 or smaller pant size will impact tape location making it slightly off centre, also the front tape clip will be removed.

Add Related Accessories.

Details

Suspenders

$110.79$125.56

Adjustable no-slip shoulder pads and chest strap. Strap length adjustment at all 4 corners.
Standard size is compatible with height up to 6’-3” @ 38” waist/pant size. XL is suitable for 6’-4” at 39” waist/pant size and up.
(Any excessive strap length is expected to be cut down to a reasonable length by the customer.)

 

* If you plan to use these suspenders with an Akribis modular set up, select the “Add 2″ Suspender Mounts” option below to make them compatible.

 

* If you want or need a 3 point system, simply cut off one of the rear suspender straps.

Dimensions: 2.5″ x 1” opening, 3” deep.

Weight: 5oz.

Add to cart

Our spacer clips are designed to slide onto our modular belts, they all integrate with our Suspender Mounts, and give one more spot where you can hang any tool with integrated hook. The most common location for Spacer Clips is the center-back, however, they can be placed wherever you have adequate room on your belt.

  • NOTE: Spacer Clips are sold individually in either a Small, Medium, or Large size. They are not sold as a set.

 

 

Combination aux hammer/knife loop. Compatible with any 2” belts.

Add to cart

 

Combination aux hammer/knife loop. Compatible with any 2” belts.

Add to cart
Details

Hook

$14.77

Stainless steel hook, compatible with any R series bag.

Add to cart
Details

Phone Holders

$25.85$29.54

Fits any phone or calculator up to 3.5” x 6.25” x ⅝”.

Phone Clip is designed to fit onto the Auxiliary Loop on L-series (Left Side) bags. Clip will only lock over a belt up to 1.5 inches. ** Clip will not close over a 2” belt.

Phone Suspender is designed to be mounted onto the 1″ chest strap of our Suspenders.

Phone Belt is designed to be mounted onto our 2” belt.

Weight: 5 ounces

2.5″ x 1” opening with 4” depth designed to accommodate a vast quantity of finishing nails. Square bottom, 11 ounce leather backing for extra durability and fibreglass rod to keep square opening.  Clip designed for the auxiliary slot on L-series and mini bags. Clip will only lock over a belt up to 1.5 inches.

Add to cart

1 x 2.5” opening with 4” depth designed to accommodate a vast quantity of finishing nails. Square bottom, 11 ounce leather backing for extra durability and fibreglass rod to keep square opening. Compatible with any 3” belt and designed to fit over the buckle of the Akribis Trimmer belt.

Add to cart

Choose from 3″ x 1 1/4” opening or 3 1/2″ x 1 1/4” opening, each with 30 degree bottom. Designed to fit up to 10 sticks of 28 – 34 degree 3 1/4” long spiker nails. This ensures a good fit and durable ware. 11 ounce leather backing for extra durability with fibreglass rod to keep square opening. Clip designed for the auxiliary slot on L-series and mini bags. Clip will only lock over a belt up to 1.5 inches.

**3″option will not fit 21 degree 3.25” stick nails.

Choose 3″ x 1 1/4″ opening  or 3 1/2″ x 1 1/4” opening with 30 degree bottom. Designed to fit up to 10 sticks of spiker nails with 30% bottom to accommodate the angle of nails. This ensures a good fit and durable ware. 11 ounce leather backing for extra durability with fibreglass rod to keep square opening.  Compatible with any 2” belts.

* 3″ option will not fit 21 degree 3.25” stick nails.

Tape clip on pocket tab with one interior pencil loop.

Add to cart

Two 11 ounce leather loops with D ring and drill clip to get drill up front and up high. Built specifically for belt pad and suspenders.

Add to cart

Two leather loops with D ring and drill clip to get drill up front and up high. Built specifically for belt pad and suspenders. Weight: 2oz

Add to cart

2 pencil slots, one utility clip. Fits Akribis Leather 1” suspender straps on top of halter square. 

Add to cart

Our Suspender Tool Loops are built to carry heavier tools, taking the weight off of your tool bags and placing it directly onto your shoulders (if wearing suspenders). The loops are designed to fit truss hooks typically installed on tools like nailers or cordless circular saws. This avoids damaging your tool bags, bending them out of shape and also provides a convenient and safe location for these tools when working from ladders, scaffolding, or on roofs.

Add to cart

7” small handles for Stitched in Place sets and 9” regular handles for Modular Looped sets. Trimmer and Framer would need to be ordered with attached suspender mounts to be compatible. Weight: 2oz

Details

LS

$14.77$62.78

LS bags are not intended to be standalone fastener bags. They are designed and intended to be a replaceable outer bag option for the vast majority of our primary fastener bags. They connect to the primary fastener bags with Chicago screws making it easy to change your outer bags to suit your work or replace a bag if it’s damaged or worn out.

*3 sets of Chicago screws included.

Note: LS bags do not come with a primary fastener bag. 

Details

LS+

$40.62$77.55

LS+ bags are not intended to be standalone fastener bags. The LS+ series of outer bags feature a micro square slot. They are designed and intended to be a replaceable outer bag option for the vast majority of our primary fastener bags. They connect to the primary fastener bags with Chicago screws making it easy to change your outer bags to suit your work or replace a bag if it’s damaged or worn out.

*3 sets of Chicago screws included.

Note: LS+ bags do not come with a primary fastener bag. 

Set of four pairs of Chicago screws ideal for simple repairs, replacing any damaged screws, attaching diagonal sheaths or outer bags. Fastener adhesive like “Loctite Threadlocker Blue” must be used on Chicago screws when attaching components.

 

Add to cart

AddOn clip is ideal for hanging cordless tools with integrated hooks or tape measure. The clip can be placed on the outer bag of your setup.

Please specify in the comments on which outer bag you would like your AddOn clip installed. If you do not specify the location, we will send you the clip, along with Chicago screws, so you can attach the clip yourself. Clips requested on any other location other than on outer bags will be sent loose with fasteners for you to install yourself.

Add to cart
Details

Mason Sleeves

$18.47$73.86

Leather sleeves fit a decorative 500ml wide mouth mason jar perfectly. Single mason sleeves, or purchase a set of 5 and save.

Details

Gift Card

$18.47$184.65

Shopping for someone else and you’re not sure what to get them? A Gift Card is great way to give them the opportunity to pick exactly what they want from Akribis.

 

***Please note: Gift cards are automatically sent to the recipient’s email upon purchase with a downloadable, printable PDF version of the gift card attached. If you’d prefer to not send an email confirmation to the person you’re purchasing the gift card for, please leave the recipient email blank or add in your own email address so you can deliver the gift card yourself.

Login to Purchase

Here's the Breakdown.

Choose your preferred currency

Here’s what you can expect for average shipping cost on small to large orders. You are responsible for duty and taxes for all international orders. You are responsible for any fees on refunds.

Canada: $15-30
US: $25-50
International: $50-120

Leather Toolbelt Illustration


Cart Breakdown: